600-HPCompact High-Power Subwoofer


Features & Benefits

• 

Efficient, high-power and high-excursion cone drivers

Extremely low distortion for low-frequency clarity

Very high peak power yields excellent transient reproduction

Low-frequency complement to MICA and other Meyer Sound self-powered loudspeakers

When fitted with MRF-600 rigging frames:

Stackable, and flyable by itself or with MICA full-range loudspeakers

Transportable in stacks using optional MCF-MICA caster frame

Applications

• 

Medium to large theatres and clubs

Houses of worship

Portable and installed A/V systems

The 600-HP is a self-powered, high-output subwoofer that may be used in both flown and ground-stacked configurations. It is designed to rig directly with MICA compact, high-power curvilinear array loudspeakers when fitted with the optional QuickFly MRF-600 rigging frame. The versatility of the 600-HP also allows it to be used with a variety of other Meyer Sound self-powered loudspeakers such as CQ-1, CQ-2, UPA-1P, UPA-2P and UPJ-1P in fixed and touring applications.

The system features two specially designed high-power 15-inch cone drivers, engineered to provide optimal performance in subwoofer applications. The high-excursion, back-vented drivers have 4-inch voice coils, and each is rated to handle 1200 watts (AES*).

The two cone drivers are housed in a rectangular, optimally tuned and vented enclosure that is the same width as MICA, and a few inches higher and deeper. The enclosure geometry makes vertical ground-stacking easy and convenient. All versions include plastic skids on the bottom of the unit to prevent damage to the enclosure or the unit below; the skids align with slots on the cabinets top to ensure secure stacking. Operating frequency range is from 36 Hz to 150 Hz, with a peak SPL at one meter of 138 dB.

Each cone driver is driven by a channel of the integral two-channel class AB/H amplifier with complementary MOSFET output stages. Total output power is 2250 watts (4500 watts peak), providing the system with sufficient headroom to accommodate the most extreme sound reinforcement demands with ease. The circuitry includes TruPower limiting to extend the life of the drivers and hold long-term power compression to less than 1 dB. The amplifier, control electronics, and power supply are integrated into a single, field-replaceable module that is mounted into the rear of the enclosure.

The optional MRF-600 rigging frame uses captive, rigid GuideALinks contained within recessed guides in the lower front and rear corners of the enclosure. A slot and convenient pinned handle allow the link to be moved and pinned for arraying or storage. The versatility of angles achieved by using combinations of front and back positions allows a MICA array suspended under 600-HP subwoofers to be uptilted for balcony coverage up to 15 degrees, or downtilted to 6 degrees with respect to the 600-HP. The 600-HP can make use of the optional MG-MICA rigging grid to accommodate a variety of flown and stacked configurations.

The durable enclosure is constructed of pre- mium birch plywood coated with a black, tex- tured hard-shell finish, with a powder-coated, hex-stamped steel grille lined with acoustical black mesh to protect the drivers. The exterior dimensions of the 600-HP are suitable for both European and U.S. trucks, and it can securely travel in stacks using the MCF-MICA caster frame, or MDB-600 dolly board when not fitted with rigging frames.

Options for the 600-HP include weather pro- tection and custom color finishes for fixed installations and other applications requiring specific cosmetics. The RMS remote monitor- ing system standard with the rigging ver- sion and optional with other configurations allows comprehensive monitoring of system parameters on a Windows-based network.

*Driven continuously for two hours with a band-limited noise signal having a 6 dB peak-to-average ratio.

 

Options

QuickFly Rigging

 

With rigging

With inset handles

Without rigging or handles

 

600-HP IN USE

Read stories about 600-HP »